ADHIAMTHERMAL 58633f908bf1620a045a5862 False 222 15
OK
background image not found
Found results for
'plate'
kelvion Replacement spares QAR   0 QAR  0
-NaN%

kelvion Replacement spares

we can support on replacement plate and gasket of Kelvion make . also, we can support on servicing of plate heat exchanger

QAR 0 QAR 0

Availability:False

Pay mode:COD only

view details
Sondex plate heat exchanger QAR   0 QAR  0
-NaN%

Sondex plate heat exchanger

AKDINDUS can supply New plate heat exchangers of Sondex Make and can support for spares and service

QAR 0 QAR 0

Availability:True

Pay mode:COD only

view details
CIP Pump QAR   0 QAR  0
-NaN%

CIP Pump

Maintenance personnels frequently encounter the problem of build-up deposits on heat transfer surfaces in many applications . We do supply the complete CIP pump system as per the requirement of our customer. The CIP pump can be used for cleaning the equipments without opening the Unit. This can be used for plate heat exchanger, spiral heat exchanger , other welded heat exchanger and shell and tube heat exchangers. Concept : Connect the CIP unit to the heat exchanger Mix the cleaning chemicals in the tank and heat it up. Circulate the cleaning solution for few hours depends on the scale. Drain and rinse thoroughly with water Disconnect the CIP unit All scales shall be removed and the equipment is back to the designed performance. Principle: Complete or partial dissolving or destruction of the deposits due to the chemical reaction. Deposits are removed in the continuous re circulation. Features and Benefits: Connecting directly to the inlet and outlet. This avoids disassembly and assembly .Down time minimized and increases the gasket life in case of gasketted phe. Construction of Pump and tank and all other wetted parts are in AISI304 or as per the preference of customer . Fast cleaning due to the hot liquid . Heating element helps to heat the chemical in the tank. Temperature Indicator to check and plan the required temperature . Reverse direction circulation makes it possible to remove any deposits which is difficult to remove from the heat exchanger.

QAR 0 QAR 0

Availability:True

Pay mode:COD only

view details
Alfa Laval Replacement spares QAR   0 QAR  0
-NaN%

Alfa Laval Replacement spares

We can support for the supply of replacement spare parts including plate and gasket.

QAR 0 QAR 0

Availability:True

Pay mode:COD only

view details
Desco coil - Plate type heatex coil QAR   0 QAR  0
-NaN%

Desco coil - Plate type heatex coil

Cooling/heating down liquids, gases, powders etc. Advantages: Low volume Large heat exchange surface Low pressure drop Suitable for high pressures

QAR 0 QAR 0

Availability:True

Pay mode:COD only

view details
Replacement Spare Gaskets QAR   0 QAR  0
-NaN%

Replacement Spare Gaskets

Plate heat exchangers gasket is one of the crucial part for the operation and it needs to consider the elastomeric properties in line with the application. An elastomer is composed of a large number of products: polymer, fillers, plasticizers, activator, accelerator, antioxidant… The formulation of an elastomer can be optimally improved to achieve desired physical traits including hardness, compression set, heat resistance and chemical properties. These parameters must be considered to choose the must appropriate elastomers for a particular gasket application. When an elastomer gasket is not used in the proper temperature range, its life can be shortened and leakage can occur. Heat plate exchanger gaskets must be designed with consideration of the following physical properties: Compression set: Hardness Tear strength: Tensile strength and elongation at break: Gasket MOC : NBR, NBR-HT, EPDM, EPDM-HT, Viton A, Viton G etc Make : Almost all makes , we can support. Some of the regular makes are

QAR 0 QAR 0

Availability:True

Pay mode:COD only

view details
Hydraulic Tightening device QAR   0 QAR  0
-NaN%

Hydraulic Tightening device

Capacity 13 - 95 ton Stroke 8 - 155 mm Center Hole Diameter 19,6 - 79,0 mm Max. Pressure 700 bar Easy to dismantle and Assemble plate pack of plate heat exchangers Less time duration to complete the assembly No possibility of misalignment of plates while assembly The tightening device shall consist of the following components : 60 Ton S/A Hollow Plunger Cylinder, Stroke: 76mm, Closed Height: 247mm Economy Pump, 3-Way Valve, Single Acting Max. operating pressure 700 bar Gauge Adaptor, 1/4" Gauge Port Pressure Gauge, Face Dia 2.5", 1/4" NPTF Thread, Range 0-10000 PSI 3/8" Hi-Flow Coupler consisting of CR400 female half & CH-604 male half 6 feet Hose, 3/8" NPTF, .25" I.D. with CH-604 Coupler 3/8" NPTF Manifold Valve, 4-Way Cylinder Half (Female) Coupler of C604 20 feet Hose, with CH-604, 3/8" NPTF, .25" I.D.

QAR 0 QAR 0

Availability:True

Pay mode:COD only

view details
Brazed Plate Heat Exchangers QAR   0 QAR  0
-NaN%

Brazed Plate Heat Exchangers

Brazed plate Heat Exchanger is constructed of a series of Pressed corrugated plates in stainless steel. These plates are stacked one over other with copper foil in between for Joining and kept in oven for brazing together. The plates are stacked in such a way that flow passage one side primary fluid and another channel secondary fluid passage. Features: Small Footprint Lower Hold-up Volume No Gaskets to Replace High and Low Temperaturesv BPHE plates and channel types Certain BPHEs are available with different types of channel plates where the herringbone pattern varies. The benefit of different herringbone patterns is that the hydraulic and thermal characteristics of the BPHE can be modified. For example, two BPHEs can have the same pressure drop on both sides despite different flow rates. The fluids can pass through the heat exchanger in different ways. For parallel flow BPHEs, there are two different flow configurations: co-current or counter-current There are several different versions of the channel plate packages. Examples include: Dual-circuit BPHEDual-circuit BPHE Two-pass BPHE, which corresponds to two units connected in series. Dual-over-two-pass BPHE Material combinations There are different BPHE product categories depending on material combinations and design pressures. The standard plate materials are AISI 316 stainless steel, S, vacuum-brazed with a pure copper filler, C, or a nickel-based filler, N. For demanding applications, the plates can be made of SMO 254, a stainless steel with a higher content of molybdenum.

QAR 0 QAR 0

Availability:True

Pay mode:COD only

view details
1
false